Configuring MTP2 - Revision history

Monica: /* Configure MTP2 in Yate */

2017-10-27T08:57:09Z

‎Configure MTP2 in Yate

2017-10-27T08:56:41Z

2017-10-27T08:52:44Z

‎Control

2017-10-27T08:45:44Z

2017-10-27T08:44:16Z

2017-10-26T08:51:58Z

‎MTP2 in YATE

2017-10-26T08:51:27Z

2017-10-26T08:51:01Z

2017-10-26T08:49:21Z

2017-10-26T08:48:51Z

‎Configuring MTP2

@@ Line 9: / Line 9: @@
 The MTP2 link is created on demand. To define a MTP2 link you must define the MTP3 linkset that uses it.
-In ysigchan.conf:
+In '''ysigchan.conf''':
   [mtp3]
@@ Line 29: / Line 29: @@
   '''Note:''' According to standards filllink should be 'yes'. We usually set it to 'no' because most of the times the underlying layers don't have support for it (unless when support was added in the hardware and then it's ok to configure filllink='yes').
-In wpcard.conf
+In '''wpcard.conf'''
   [wanpipe1]

@@ Line 1: / Line 1: @@
-==Implementation==
+This is a short example on how to configure MTP2 in Yate.
-MTP2 implementation in YATE is located in ysig library. The methods declaration is in libs/ysig/yatesig.h and the implementation in libs/ysig/layer2.cpp. Class name is SS7MTP2.
-==Example==
+==Installing sangoma cards==
 Follow [http://docs.yate.ro/wiki/VoIP_PSTN_Gateway#Installing_Sangoma_cards_under_Linux this guide] to install sangoma cards under Linux.
 The MTP2 link is created on demand. To define a MTP2 link you must define the MTP3 linkset that uses it.
 In ysigchan.conf:
   [mtp3]
   type=ss7-mtp3
@@ Line 36: / Line 36: @@
   voicegroup=w1g2

← Older revision		Revision as of 08:52, 27 October 2017
Line 86:		Line 86:
	\|Align \|\| control MTP2_NAME align \|\| Force this to start Align algorithm		\|Align \|\| control MTP2_NAME align \|\| Force this to start Align algorithm
	\|}		\|}
		+
		+
		+	'''See also'''
		+
		+	* [[SS7 MTP2 in Yate]]

← Older revision		Revision as of 08:45, 27 October 2017
Line 1:		Line 1:
−	~~This is a short guide to configure MTP2 in Yate.~~
−
−
	The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].<br>		The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].<br>
	MTP2 configurations depends both on the local TDM card and on the remote side requirements.		MTP2 configurations depends both on the local TDM card and on the remote side requirements.

@@ Line 1: / Line 1: @@
-==MTP2 in YATE==
+This is a short guide to configure MTP2 in Yate.
 The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].<br>
 MTP2 configurations depends both on the local TDM card and on the remote side requirements.
-===Implementation===
+==Implementation==
 MTP2 implementation in YATE is located in ysig library. The methods declaration is in libs/ysig/yatesig.h and the implementation in libs/ysig/layer2.cpp. Class name is SS7MTP2.
-===Example===
+==Example==
 Follow [http://docs.yate.ro/wiki/VoIP_PSTN_Gateway#Installing_Sangoma_cards_under_Linux this guide] to install sangoma cards under Linux.
@@ Line 38: / Line 39: @@
   voicegroup=w1g2
-===Configuration===
+==Configuration==
 From sample ysigchan.conf file:
@@ Line 76: / Line 77: @@
   ;layer2dump=
-===Status===
+==Status==
-===Control===
+==Control==
 MTP2 Control commands:

@@ Line 2: / Line 2: @@
 The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].
 MTP2 depends both on the local TDM card and on the remote side requirements.
-[[Configure MTP2|Configuration]] of these links depends both on the local TDM card and on the remote side requirements.
 ===Implementation===

← Older revision		Revision as of 08:49, 26 October 2017
Line 1:		Line 1:
−	==~~Configure~~ MTP2==	+	==MTP2 in YATE==

	The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].		The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].

← Older revision		Revision as of 08:48, 26 October 2017
Line 1:		Line 1:
−	== [[Configure MTP2~~\|Configuring MTP2]]~~==	+	==Configure MTP2==

	The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].		The [http://en.wikipedia.org/wiki/Message_Transfer_Part#Signalling_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].