Cpuload - Revision history

Andrei at 12:54, 18 July 2016

2016-07-18T12:54:17Z

Monica at 11:28, 4 November 2013

2013-11-04T11:28:53Z

Dana at 14:30, 19 October 2012

2012-10-19T14:30:02Z

Dana: Created page with " File cpuload.conf ; NOTE this file is used to setup CPU load information's ; The cpuload module inform YATE about system total CPU load and YATE CPU load ;[general] ; Th..."

2012-10-19T14:27:42Z

Created page with " File cpuload.conf ; NOTE this file is used to setup CPU load information's ; The cpuload module inform YATE about system total CPU load and YATE CPU load ;[general] ; Th..."

New page

File cpuload.conf

; NOTE this file is used to setup CPU load information's
; The cpuload module inform YATE about system total CPU load and YATE CPU load

;[general]

; This section keeps the settings for system and Yate.

; interval: int: The interval in milliseconds for CPU load check.
; Note: Minimum value is 1s.
; Default value 1s
; interval=1000

; oscillate_interval : int: Time in milliseconds that stop this module from notifying about CPU load,
; if the CPU load is oscillating between consecutive intervals
; NOTE! oscillate_interval value should be at least 2 * interval
; oscillate_interval=5000

; core_number: integer: The number of CPU cores
; NOTE! Yate will detect the number of cores from "/proc/stat". If the file does not exists you should
; set the core number to avoid that yate CPU load to be bigger than 100%
; core_number=1

; smooth : integer between 5 and 50 : Value used to smooth the CPU loading.
; smooth = 33

;The following sections represent the CPU load managers.

; NOTE!!! Each parameter form the following sections need to match this type:
; target_name=interval_name,threshold_value,hysteresis_value;......
; target_name: string: The name if the target.
; interval_name : string: The name of the interval.
; threshold_value: int: The upper value of the interval.
; hysteresis_value: int.

; Examples: engine=accept,50,4;partial,65,2;congestion,80,2;reject
; The target is "engine";
; Interval names: all, partial,congestion,none;
; Threshold value: 50, 65, 80
; from this results two sets of intervals:

; one when the CPU load is growing :
; accept = 0-54
; partial = 54 - 67
; congestion = 67 - 82
; reject = 82 - 100

; two when CPU load is lowering
; accept = 0-46
; partial = 46 - 63
; congestion = 63 - 78
; reject = 78 - 100

; '''NOTE!''' : Parameters can be appended with chan.control message and with rmanager command
; '''Example''': [[rmanager]]

; "control cpuload section target_name=interval_name,threshold_value,hysteresis_value;......"

; where "section" represents one from the sections above

; '''Example: [[chan.control]]'''
; Message* m = new Message("chan.control");
; m->addParam("targetid","cpuload");
; m->addParam("component","cpuload");
; m->addParam("operation",monitor); // One of the following : kernelLoad,userLoad,totalLoad,systemLoad
; m->addParam("engine","interval_name,threshold_value,hysteresis_value;...... ");
; Engine::enqueue(m); // Engine::dispatch(m);

; '''NOTE! ''': Target "engine" is reserved for engine call accept. If you want to modify engine monitors
; or intervals please do it form manager.conf

;[kernelLoad]
; YATE CPU kernel-space load settings

;[userLoad]
; YATE CPU user-space load settings

;[totalLoad]
; YATE CPU load settings

;[systemLoad]
; System CPU load settings

← Older revision		Revision as of 12:54, 18 July 2016
Line 87:		Line 87:
	; System CPU load settings		; System CPU load settings

		+	; The module can be queried for load information
		+	; '''Example: [[monitor.query]]'''
		+	; Message* m = new Message("monitor.query");
		+	; m->addParam("name","load_name");
		+	; Where load_name can be one of the following: kernelLoad,userLoad,totalLoad,systemLoad
		+
		+
	[[Category:Monitoring]] [[Category:CPULoad]]		[[Category:Monitoring]] [[Category:CPULoad]]

← Older revision		Revision as of 11:28, 4 November 2013
Line 86:		Line 86:
	;[systemLoad]		;[systemLoad]
	; System CPU load settings		; System CPU load settings
		+
		+	[[Category:Monitoring]] [[Category:CPULoad]]

@@ Line 2: / Line 2: @@
 File cpuload.conf
+ ; NOTE this file is used to setup CPU load information's
+ ; The cpuload module inform YATE about system total CPU load and YATE CPU load
 ; NOTE this file is used to setup CPU load information's
-; The cpuload module inform YATE about system total CPU load and YATE CPU load
+ ;[general]
-−
-;[general]
+ ; This section keeps the settings for system and Yate.
-−
-; This section keeps the settings for system and Yate.
+ ; interval: int: The interval in milliseconds for CPU load check.
+ ; Note: Minimum value is 1s.
-; interval: int: The interval in milliseconds for CPU load check.
+ ; Default value 1s
-; Note: Minimum value is 1s.
+ ; interval=1000
 ; Default value 1s
-; interval=1000
+ ; oscillate_interval : int: Time in milliseconds that stop this module from notifying about CPU load,
+ ; if the CPU load is oscillating between consecutive intervals
-; oscillate_interval : int: Time in milliseconds that stop this module from notifying about CPU load,
+ ; NOTE! oscillate_interval value should be at least 2 * interval
-; if the CPU load is oscillating between consecutive intervals
+ ; oscillate_interval=5000
 ; NOTE! oscillate_interval value should be at least 2 * interval
-; oscillate_interval=5000
+ ; core_number: integer: The number of CPU cores
+ ; NOTE! Yate will detect the number of cores from "/proc/stat". If the file does not exists you should
-; core_number: integer: The number of CPU cores
+ ; set the core number to avoid that yate CPU load to be bigger than 100%
-; NOTE! Yate will detect the number of cores from "/proc/stat". If the file does not exists you should
+ ; core_number=1
 ; set the core number to avoid that yate CPU load to be bigger than 100%
-; core_number=1
+ ; smooth : integer between 5 and 50 : Value used to smooth the CPU loading.
+ ; smooth = 33
 ; smooth : integer between 5 and 50 : Value used to smooth the CPU loading.
-; smooth = 33
+ ;The following sections represent the CPU load managers.
-−
-;The following sections represent the CPU load managers.
+ ; '''NOTE!!!''' Each parameter form the following sections need to match this type:
+ ; ''target_name''=interval_name,threshold_value,hysteresis_value;......
-; NOTE!!! Each parameter form the following sections need to match this type:
+ ; ''target_name'': string: The name if the target.
-; target_name=interval_name,threshold_value,hysteresis_value;......
+ ; ''interval_name'' : string: The name of the interval.
-; target_name: string: The name if the target.
+ ; ''threshold_value'': int: The upper value of the interval.
-; interval_name : string: The name of the interval.
+ ; ''hysteresis_value'': int.
 ; threshold_value: int: The upper value of the interval.
-; hysteresis_value: int.
+ ; Examples: engine=accept,50,4;partial,65,2;congestion,80,2;reject
+ ; The target is "engine";
-; Examples: engine=accept,50,4;partial,65,2;congestion,80,2;reject
+ ; Interval names: all, partial,congestion,none;
-; The target is "engine";
+ ; Threshold value: 50, 65, 80
-; Interval names: all, partial,congestion,none;
+ ; from this results two sets of intervals:
 ; Threshold value: 50, 65, 80
-; from this results two sets of intervals:
+ ; one when the CPU load is growing :
+ ; accept = 0-54
-; one when the CPU load is growing :
+ ; partial = 54 - 67
-; accept = 0-54
+ ; congestion = 67 - 82
-; partial = 54 - 67
+ ; reject = 82 - 100
 ; congestion = 67 - 82
-; reject = 82 - 100
+ ; two when CPU load is lowering
+ ; accept = 0-46
-; two when CPU load is lowering
+ ; partial = 46 - 63
-; accept = 0-46
+ ; congestion = 63 - 78
-; partial = 46 - 63
+ ; reject = 78 - 100
 ; congestion = 63 - 78
-; reject = 78 - 100
+ ; '''NOTE!''' : Parameters can be appended with chan.control message and with rmanager command
+ ; '''Example''': [[rmanager]]
 ; '''NOTE!''' : Parameters can be appended with chan.control message and with rmanager command
-; '''Example''': [[rmanager]]
+ ;  "control cpuload section target_name=interval_name,threshold_value,hysteresis_value;......"
-−
-;  "control cpuload section target_name=interval_name,threshold_value,hysteresis_value;......"
+ ; where "section" represents one from the sections above
-−
-; where "section" represents one from the sections above
+ ; '''Example: [[chan.control]]'''
+ ; Message* m = new Message("chan.control");
-; '''Example: [[chan.control]]'''
+ ; m->addParam("targetid","cpuload");
-; Message* m = new Message("chan.control");
+ ; m->addParam("component","cpuload");
-; m->addParam("targetid","cpuload");
+ ; m->addParam("operation",monitor); // One of the following : kernelLoad,userLoad,totalLoad,systemLoad
-; m->addParam("component","cpuload");
+ ; m->addParam("engine","interval_name,threshold_value,hysteresis_value;...... ");
-; m->addParam("operation",monitor); // One of the following : kernelLoad,userLoad,totalLoad,systemLoad
+ ; Engine::enqueue(m); // Engine::dispatch(m);
 ; m->addParam("engine","interval_name,threshold_value,hysteresis_value;...... ");
-; Engine::enqueue(m); // Engine::dispatch(m);
+ ; '''NOTE! ''': Target "engine" is reserved for engine call accept. If you want to modify engine monitors
+ ; or intervals please do it form manager.conf
 ; '''NOTE! ''': Target "engine" is reserved for engine call accept. If you want to modify engine monitors
-; or intervals please do it form manager.conf
+ ;[kernelLoad]
+ ; YATE CPU kernel-space load settings
 ;[kernelLoad]
 ; YATE CPU kernel-space load settings
+ ;[userLoad]
+ ; YATE CPU user-space load settings
 ;[userLoad]
 ; YATE CPU user-space load settings
+ ;[totalLoad]
+ ; YATE CPU load settings
 ;[totalLoad]
 ; YATE CPU load settings
+ ;[systemLoad]
+ ; System CPU load settings
 ;[systemLoad]
 ; System CPU load settings