Fax Transfer Module - Revision history

Monica: /* Network Traffic Capture */

2013-11-04T10:09:06Z

‎Network Traffic Capture

2013-06-10T14:10:41Z

‎Network Traffic Capture

2013-06-10T14:09:20Z

‎How to use faxchan module

2013-06-10T14:03:42Z

‎Questions & Answers

2013-06-10T14:02:32Z

2013-06-10T14:00:11Z

2012-11-06T13:28:26Z

2012-11-06T13:17:21Z

2012-11-06T13:16:31Z

‎Questions & Answers

2012-11-06T13:16:10Z

‎Questions & Answers

← Older revision		Revision as of 10:09, 4 November 2013
Line 135:		Line 135:
	* [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]		* [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]
	* [[Modules]]		* [[Modules]]
		+
		+	[[Category:T.38]] [[Category:FAX]]

← Older revision		Revision as of 14:10, 10 June 2013
Line 134:		Line 134:

	* [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]		* [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]
		+	* [[Modules]]

@@ Line 55: / Line 55: @@
 You will still need to set the debugging level on the fax channels to 9 or 10 to see spandsp FLOW or DEBUG.
-'''IMPORTANT''': The spandsp library logs '''only to file'''. You will not see any output in ramanager. Always copy the output from the log file, not from rmanager session.
+'''IMPORTANT''': The spandsp library logs '''only to file'''. You will not see any output in rmanager. Always copy the output from the log file, not from rmanager session.
 Please note that the old fax channel in Yate 0.8 had an extra element. This has been replaced with the ''faxcaller'' message parameter which is safer and more flexible.

@@ Line 92: / Line 92: @@
 ===Questions & Answers===
-'''How do I enable T.38?'''
+====How do I enable T.38?====
 I did not have to do anything to enable T.38 - it is supported by my upstream provider (which uses Dialogic-SIP). The connection for incoming faxes will start in 'classic' SIP mode and switch to T.38.
-'''How can I configure the faxchan module?'''
+====How can I configure the faxchan module?====
 No configuration file exists for this module - no configuration needs to be done.
 ===Debugging===

@@ Line 16: / Line 16: @@
   ^2$=fax/receive/path/to/rx-file.tiff
 The best way to use this module is an external module written in php (maybe) that can handle the name of the tiff file and maybe a forwarding to a mail.
@@ Line 58: / Line 60: @@
 Also note that the ''faxecm'' default was false before [http://yate.null.ro/websvn/revision.php?repname=yate&path=%2Ftrunk%2F&rev=2413 SVN Revision 2413]
 ===Sample setup===
@@ Line 131: / Line 132: @@
-===Further reading===
+'''See also'''
 * [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]

@@ Line 1: / Line 1: @@
 This module can be used either to send or receive a fax from a local file.
@@ Line 6: / Line 4: @@
 Since the spandsp library evolves and the API changes you are advised to download and use version [http://www.soft-switch.org/downloads/spandsp/spandsp-0.0.6pre3.tgz 0.0.6 pre 3], also available [http://yate.null.ro/tarballs/spandsp-0.0.6pre3.tgz here]. Other versions may not be detected during configuration or may fail to build or run properly.
 In regexroute.conf you can set this to transmit a fax:
   ^1$=fax/transmit/path/to/tx-file.tiff
 To receive a fax you can use this:

← Older revision		Revision as of 13:28, 6 November 2012
Line 127:		Line 127:

	There should be a SIP/SDP invite message containing Media Attributes in its Message Body, i.e. T38FaxVersion, T38MaxBitRate, T38FaxMaxBuffer, etc.		There should be a SIP/SDP invite message containing Media Attributes in its Message Body, i.e. T38FaxVersion, T38MaxBitRate, T38FaxMaxBuffer, etc.
		+
		+
		+	===Further reading===
		+	* [http://soft-switch.org/foip.html Why T.38 makes sense, and Fax over VoIP without it fails]

@@ Line 85: / Line 85: @@
 '''There is no such file - no configuration needed / possible'''
 ===Questions & Answers===
@@ Line 95: / Line 96: @@
 No configuration file exists for this module - no configuration needs to be done.
 ===Debugging===
 ====Log====
 Enable verbose logging (-vvvvvvvvvvv) when starting YATE.