Accfile

Revision as of 11:01, 19 November 2012

This file is used when Yate is registering itself to a remote server.

General parameters

• protocol: The protocol to register on (sip, iax, h323, jabber ...)
• username: Account username
• password: Account password
• interval: Registration interval (in seconds) to request from server (ignored for jabber)
• enabled:

Sections with enabled=no are always ignored.

If the enabled parameter is missing sections without username are ignored.

If enabled=yes the accounts are logged in even without an username.

Specific parameters

SIP

• description: Caller name to set on outgoing calls on this account if none specified when routing
• registrar: Registrar address. A port can be specified here (e.g. 1.2.3.4:7999)
• authname: Authentication name to use instead of username when authenticating
• domain: Authentication domain if any
• outbound: Optional outbound proxy server if different from registrar.

A port can be specified here (e.g. 1.2.3.4:7999)

• ip_transport: Optional SIP transport to use (udp, tcp, tls).

Defaults to udp

• ip_transport_remoteip: IP address to connect to register the account.

Defaults to outbound or registrar address

• ip_transport_remoteport: IP port to connect to register the account
• ip_transport_localip: UDP: This parameter is used in conjuction ip_transport_localport

to identify the transport to use

TCP/TLS: Optional local ip to use when connecting

• ip_transport_localport: Local port.

UDP only: This parameter is used to identify the transport to use

• localaddress: Local address to set in sent messages

Set it to 'yes' to detect NAT and re-register with public ip when NAT is detected

Set it to 'no' or ipaddress (e.g. 1.2.3.4 or 1.2.3.4:5060) to disable NAT detection

• keepalive: Optional interval for NAT keep alive.

Defaults to 0 if NAT detection is disabled

NOTE

Default port is 5060 for udp/tcp and 5061 for tls

Jabber

• domain: Authentication domain
• port: Server port. Defaults to 5222
• server: Optional jabber server ip address to connect to.

If set the jabber stream will try first to connect to this address

• localip: Optional local ip address to use when connecting.

Connect will fail if the address is invalid

• resource: Optional resource to request from server
• priority: Optional resource priority to set in initial presence
• options: Comma separated list of stream flags

- allowplainauth: Allow plain password authentication

- tlsrequired: Stream encryption is required

- noautorestart: Don't restart the stream when disconnected (NOT RECOMMENDED)

• nocompression: Boolean. Set it to 'yes' to disable stream compression

IAX

• server: Registrar address or domain. A port can be specified here (e.g. 1.2.3.4:7999)
• port: Registrar port if not specified in 'server' parameter

If not set the port defaults to 4569

H323

• server: Registrar IP address
• addr: Local address for H323 listener (leave it empty to listen on all interfaces)
• port: Local port for H323 listener

Configuration

accfile.conf

[test_sip]
enabled=no
protocol=sip
;username=me
description=Test SIP account
;interval=600
;authname=metoo
;password=1234
;domain=somewhere.org
;registrar=10.0.0.1:5060
;outbound=10.0.0.1:5061
;localaddress=192.168.0.1:5062
;
[test_h323]
enabled=no
protocol=h323
;username=me
description=Test H.323 account
;interval=600
;password=1234
;
[test_iax]
enabled=no
protocol=iax
;username=me
description=Test IAX2 account
;interval=600
;password=1234
;server=10.0.0.2
;
[test_jabber]
enabled=no
protocol=jabber
;username=me
;domain=example.com
;password=1234
;options=allowplainauth