How to configure ISUP in Yate

Latest revision as of 14:23, 26 October 2017

We will setup a ISUP configuration in Yate to make calls.
Below is a image that describes the configuration.
So there are 2 Yate that are configured as a softswitch, each of them will act as a SIP server and a SS7 SEP in the network. The Clients used will be Yate SIP Clients that will communicate with Yate on SIP protocol, then the call is routed through SS7 to the corresponding SEP. The message will be read at each level in the order shown in the image: SCTP, M2PA, MTP3, ISUP and then routed in SIP and send to the destination.

[edit] ISUP configuration

[edit] Prerequisite

• SCTP:

On the machines where ISUP will be configured SCTP must be installed and compiled.

• Yate:

Download a copy of Yate

Yate needs to be configured with command: ./configure --enable-sctp=yes.

[edit] Parameters & Source

Parameters:

• pointcodetype
• format
• remotepointcode
• lockgroup
• earlyacm
• inn
• numplan
• numtype
• presentation
• screening
• callercategory
• channelsync
• userparttest
• t9
• continuity
• confirm_ccr
• drop_unknown
• ignore-grs-single
• ignore-cgb-single
• ignore-cgu-single
• duplicate-cgb
• parttestmsg
• ignore-unknown-digits
• sls
• maxcalleddigits
• print-messages
• extended-debug

Source:

• libs/ysig/isup.cpp

[edit] Building the setup

We are going to use 2 Softswitches with Yate installed and configured with ISUP to make calls (see the configuration for Server1 and Server2).
Each ISUP will have the same list of circuits.
The transport will be done over SCTP and is set in sigtransport.conf file.
The configuration of SS7 signaling will be done in ysigchan.conf and will consist of: Linkset: MTP3, Link: m2pa and Trunk: ISUP.
The voice is configured in mgcpca.conf.

For transmitting the voice another machine will be used (see Server3) that will act as a Media Gateway.

[edit] Server1 (IP:192.168.168.156)

Transport it is done over SCTP:

sigtransport.conf

;The name of the section identifies the connection
[sctp-m2pa]
type=sctp
stream=false
;Primary local address
local=192.168.168.156:5050
remote=192.168.168.200:6999

SS7 signalling configuration

ysigchan.conf

;SS7 MTP3 network (linkset)
[mtp3]
type=ss7-mtp3
;Comma separated list of point code types used to map an
;incoming network indicator to a specific point code type
netind2pctype=ITU
netindicator=national
;Declare a local pointcode for the SS7 network
local=ITU,0-0-6
;Build an adjacent route for the SS7 network
adjacent=ITU,0-0-5
;Name of a SS7 Layer 2 link to create in the linkset
link=m2pa

;SS7 M2PA link
[m2pa]
type=ss7-m2pa
sig=sctp-m2pa

;SS7 ISUP trunk
[isup]
type=ss7-isup
netindicator=national
pointcodetype=ITU
pointcode=0-0-6
remotepointcode=5
defaultpointcode=6
voice=mgcpca

Voice it is set in:

mgcpca.conf

[gw mgcpca]
user=ACgw101
host=192.168.168.77
port=2427
address=192.168.168.77
voicechans=1-15.17-31
chans=31
start=1

[engine]

Configure user for test:

regfile.conf

[333]
password=mysecret1

[edit] Server2 (IP:192.168.168.200)

Transport it is done over SCTP:

sigtransport.conf

[sctp-m2pa]
type=sctp
stream=false
local=192.168.168.200:6999
remote=192.168.168.156:5050

SS7 signalling configuration:

ysigchan.conf

[mtp3]
type=ss7-mtp3
netind2pctype=ITU
netindicator=national
local=ITU,0-0-5
adjacent=ITU,0-0-6
link=m2pa

[m2pa]
type=ss7-m2pa
sig=sctp-m2pa

[isup]
type=ss7-isup
netindicator=national
pointcodetype=ITU
pointcode=0-0-5
remotepointcode=6
defaultpointcode=5
voice=mgcpca

Voice it is set in:

mgcpca.conf

[gw mgcpca]
user=ACgw101
host=192.168.168.77
port=2427
address=192.168.168.77
voicechans=1-15.17-31
chans=31
start=1

[engine]

Configure user for test:

regfile.conf

[222]
password=mysecret2

regexroute.conf

[default]
.*=sig/\0;trunk=isup

[edit] Server3 (IP:192.168.168.77)

Configuring mgcp gateway and the 2 EndPoints that are set in each machine (in Server1 and in Server2):

mgcpgw.conf

[engine]
enabled=yes
address=0.0.0.0
request_ack=no
send_provisional=no
retrans_interval=0
retrans_count=0

[ep ACgw100]
local_user=ACgw100
local_host=192.168.168.77
remote_host=192.168.168.200

[ep ACgw101]
local_user=ACgw101
local_host=192.168.168.77
remote_host=192.168.168.156

regexroute.conf

[default]
.*=dumb/

[edit] Testing the setup

Server1 and Server2 are started then Server3.
Two Yate clients can be used to register the users configured. Then calls are made from one client to another.

See also

• SS7 Setups