Search results

Page title matches

• SS7 MTP2 in Yate
  ...g_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].<br> MTP2 configurations depends both on the local TDM card and on the remote side re
  2 KB (297 words) - 08:55, 27 October 2017

Page text matches

• How To's
  ...es and signalling modules. Here you can find some how to's for configuring Yate using different modules. {|class="yate-table"
  9 KB (1,376 words) - 10:01, 27 October 2017
• Telephony
  {|class="yate-table" |class="yate-header-left"|'''About'''
  8 KB (1,083 words) - 11:49, 27 October 2017
• Modules
  By default Yate loads modules relevant to its current running mode: * in client mode modules from the client subdirectory
  12 KB (1,662 words) - 13:25, 1 October 2019
• Configuring MTP2
  This is a short example on how to configure MTP2 in Yate. Follow [http://docs.yate.ro/wiki/VoIP_PSTN_Gateway#Installing_Sangoma_cards_under_Linux this guide]
  975 B (160 words) - 08:57, 27 October 2017
• Configuring M2PA
  ... replace MTP2 protocol in the IP scenarios. M2PA has some advantages over MTP2: * The traffic is not limited to classical 64 Kb/s SS7 link speed.
  6 KB (958 words) - 10:45, 26 October 2017
• Configure M2UA
  ...er 3 present on the gateway side because the M2UA gateway itself acts as a SS7 layer 3 without the capability of directly controlling the supervised layer ... clients requested so. This behavior will let the following responsibility in the hands of the gateway:
  13 KB (2,284 words) - 11:12, 13 December 2017
• Configure MTP3
  ...des network management and controls traffic when congestion occurs. When a MTP2 data link is no longer available it establishes alternative links and re-ro Each network element in a SS7 network is uniquely identified by a Point Code (PC). The routing of the mes
  7 KB (1,115 words) - 10:47, 27 October 2017
• Configure Cisco SLT
  Configuring a MTP2 backhaul with Cisco SLT requires configuring both ends, applying configurat '''IMPORTANT''': Cisco gateways support a maximum of 4 SS7 links.<br/>This is enough for small configurations but insufficient to corr
  10 KB (1,328 words) - 09:09, 26 October 2017
• Configure Mediant M2UA
  ... ''PSTN Settings'' => ''Trunk Settings''. For each trunk you configure for SS7/MGCP select ''Protocol Type'' => ''E1 transparent 31'' or ''T1 TRANSPARENT' Repeat to create all groups you need. In this example create just one group number 0 port 2904.
  6 KB (975 words) - 13:22, 26 October 2017
• Miscellaneous configurations
  Various configuration examples of combinations of SS7 features in Yate. ; type=ss7-m2ua-gateway
  15 KB (1,985 words) - 10:45, 27 October 2017
• SCCP Introduction
  SCCP represents a layer 4 protocol from SS7 signaling stack. It runs over a SS7 layer 3 protocol like MTP3 or M3UA.
  11 KB (1,757 words) - 09:19, 27 October 2017
• SS7 Implementation
  In Yate the following SS7 components are implemented: ...ules in Yate are [http://docs.yate.ro/wiki/Wpcard wpcard] and [http://docs.yate.ro/wiki/Zapcard zapcard]. Note that the same modules provide ISDN D-Channel
  3 KB (569 words) - 08:36, 27 October 2017
• Ysigchan
  *Handle the SS7 protocol (management, maintenance, routing). ...r module(s) (e.g. [http://docs.yate.ro/wiki/Zapcard zapcard], [http://docs.yate.ro/wiki/Wpcard wpcard]) to create interfaces and circuits used to transfer
  36 KB (5,180 words) - 12:18, 26 October 2017
• Signalling
  ...ef introduction on how the PSTN signalling modules are working together in Yate. The [http://docs.yate.ro/wiki/Analog analog] module provides the common call control logic.
  5 KB (749 words) - 12:56, 26 October 2017
• SS7 MTP2 in Yate
  ...g_Link_Functional_Level MTP2] links are the classic way of interconnecting SS7 over [http://en.wikipedia.org/wiki/Time-division_multiplexing TDM].<br> MTP2 configurations depends both on the local TDM card and on the remote side re
  2 KB (297 words) - 08:55, 27 October 2017